Job Description SummaryPerform general maintenance support under minimal supervision, support daily operations, facility infrastructure and projects. CNC machine control troubleshooting and repair. Support lean activities, construction projects, hazardous waste management and energy conservation programs/projects. Possess general knowledge and understanding of Company policies and procedures and be able to apply Environmental, Health and Safety processes to daily assigned tasks and projects.Job DescriptionWages are $22.80 - $30.23 per hour based on experience.Essential Duties and ResponsibilitiesPerforms general labor throughout the facility and preventive maintenance tasksTroubleshoots and repairs equipmentPerforms preventative maintenance to ensure that building and manufacturing operations equipment continue to operate in a safe and effective manner while moving towards the goal of "no unplanned downtime"Suggests upgrades/retrofits for greater reliability and efficiencyMust be able to read wiring diagrams and be able to wire 110V, 220V, and 480V circuits- single and three phase; good understanding of control circuitsProcesses work ordersMaintain spare parts inventory and supplies as needed to control machine down timePerforms equipment checks and manage outside servicesResponsible for safe chemical and hazardous waste handlingResponds to emergency situations: turns off equipment or utilities as required and initiates clean up or containment actions on hazardous materials as appropriate by certificationRecommends program and preventative maintenance improvements to enhance building and facility system reliabilityRepairs all machinery within the facilityRecognizes when a possible breakage of machine parts could occur during disassembly and will seek assistance with other technicians and drawings to determine the best way to disassemble the component safelyAble to install and maintain tubing and related hydraulic and pneumatic equipment, repairs or replaces gauges, valves, pumps, and related componentsAble to communicate to leadership in a reasonable amount of time the machine problem and suggest some possible completion timesOperates forklift, scissor lift, aerial lift as neededMust be able to work overtime and on occasion may be called during off hours or weekends to support emergency situationsOn occasion may require guidance for contractors and/or Non-GE purchased service providersMust have a strong background in electronics and be able to use test equipment such as oscilloscope and other digital test equipmentMay be required to install or repair automated machinery and equipment such as tool changers or programmable controllersAbility to read electrical, pneumatic and hydraulic blueprints & schematics to assist in troubleshooting and repairing machine toolsRead and Interpret machine tool ladder within the CNC control and printouts to assist in troubleshootingHave a good basic knowledge in CNC part programmingAbility to use the MDI function on CNC machines to assist in troubleshootingAbility to design, install and test electrical and or electronic circuits on CNC and conventional machines for safe operation by qualified personnelAbility to Inspect parts to determine if they should be replaced or reworked and able to find part numbers for ordering and expediting repairsInstalls and Inspects 3 phase AC motors, DC motors and know when they are in need of repairBasic knowledge of Programmable Logic controllers (PLCs) and Electronic Controllers and programming languageKnowledge to replace printed circuit boards, servo drives, and power suppliesAbility to set jumpers or parameters in these devicesPlans and schedules maintenance activities not to interrupt normal production as necessaryMay train other maintenance workers in proper technique and proceduresMay install or repair automated machinery and equipment such as tool changers or programmable controllersWork to established Lean Manufacturing guidelinesComply to all safety policies and procedures such as LOTO, Arc Flash, etc.Work under general direction with minimal coaching in a team environmentWill also perform other duties and special projects as assignedQualificationsTo perform this job successfully, an individual must be able to perform each essential duty satisfactorily. Also, proven ability to demonstrate:Compliance with and supports all GE policies and the "Integrity: The Spirit and The Letter of Our Commitment" guideExcellent customer service to co-workers, customers, and vendorsEmbraces ambiguity and engages others in idea generationWorks collaboratively and respects all othersActively participate and support a team environmentKeeps team informed of work progress, timelines, and issuesEducation AND/OR EXPERIENCEHigh school diploma or General education Degree (GED), plus 3+ years of facility maintenance or related experience and/or training: or equivalent combination of education and experience. Minimum of 3 years of experience in troubleshooting and repairing CNC machine tools and/or training; or equivalent combination of education and experience. Two year degree or trade school completion is preferred.Demonstrated work experience or successful completion of classes in reading and interpreting blueprints.This role requires access to U.S. export-controlled information. If applicable, final offers will be contingent on ability to obtain authorization for access to U.S. export-controlled information from the U.S. Government.Additional InformationGE offers a great work environment, professional development, challenging careers, and competitive compensation. GE is anEqual Opportunity Employer.Employment decisions are made without regard to race, color, religion, national or ethnic origin, sex, sexual orientation, gender identity or expression, age, disability, protected veteran status or other characteristics protected by law.GE will only employ those who are legally authorized to work in the United States for this opening. Any offer of employment is conditioned upon the successful completion of a drug screen (as applicable).Relocation Assistance Provided:No
